Description
Unique feature that dissociates slop to seperate oil and water. This product is formulated to meet the ever changing regulations for the treatment of tank cleaning waste water after using petroleum based solvents, and Bunker “C” cleaners.
Technical Bulletin
Chem Break Rx ORG-RXSOL-20-2006-025 ( SLUDGE BREAK )
For Engine Room & Cargo Tank Cleaner
Product Description:- RXSOL-20-2006-025 is an all purpose degreaser emulsifiers, It is an excellent blend of powerful solvent base and emulsifying inorganic products .Specially designed for engine room and cargo tank cleaning .Main feature of RXSOL-20-2006-025 is, it finally dissociate slop emulsion to separate oil and water .This provide us with ability to dispose of waste solution as per MARPOL & IMO rules and regulation .
Dosage:- Dose rate and results will vary depending on amount of contamination . For light contamination dilution with water up to 1:20 is recommended where as medium contamination dilution with Petro solvent , And for heavy contamination neat RXSOL CB 2006 is suggested to use.
Procedure of use :- RXSOL-20-2006-025 is recommended for local cleaning & degreasing of engine rooms, bilges & tank tops. It may be applied by brush, spray, immersion, soaking, or any other conventional means.RXSOL-20-2006-025 is used neat. Allow a residence time of at least 20- 45 minutes where possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed to separate in a holding tank for atleast 3-5 hours before passing through an oily water separator.
Tank Cleaning after Mineral Oils/ Lube Oils / Slope-Black Oil
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a temperature between 65°C & 80°C then stripped constantly and transferred to a holding tank for separation.The time for this will vary depending on amount of RXSOL-20-2006-025 used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly RXSOL-20-2006-025 on tank surfaces to be cleaned, left for at least 30 minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.
Product Properties:-
|
Appearence |
Clear (Raw material depended colour of the effectively will , however not be impaired .) |
|
|
|
Density |
In g/cm3 at 15°C: 0.93 |
|
|
|
Flash Point |
(PMCC)°C: Above 66 |
|
|
|
Compatibility |
|
|
|
|
Metal |
No known effect |
|
|
|
Rubber |
Do not use with natural rubber compounds |
|
|
|
Synthetic Rubber |
May swell |
|
|
|
Packaging |
Order No |
Size (in Litres) |
|
|
|
RXSOL-20-2006-025 |
25 , 35 , 210 |
|
Characteristics:-
High penetration & emulsification , Reduces down time.
Low toxicity, non -corrosive. Highly effective, economical solvent cleaner.
For cleaning of machinery parts, bulk heads, decks, bottom plates & any oil/grease dirty areas.
Used for cargo tank cleaning of mineral oils and petroleum based chemicals .
Label
RXSOL-20-2006 has the unique feature that dissociates slop to seperate oil and water. This product is formulated to meet the ever changing regulations for the treatment of tank cleaning waste water after using petroleum based solvents, and Bunker “C” cleaners.
LABEL PROPERTY
Odour …………………….. Smells of hydrocarbon
Appearance ……………. Liquid, brown,
pH ………………………….. not applicable
Boiling point ……………. 195 °C at 760 mm /Hg
Vapour pressure ……… 1 mbar
Vapour density ………… (air = 1) >1
Melting point ……………. not known
Insoluble in water …….. Specific gravity /(water=1) 0.79
Flash point ……………. 66 deg C (CC)
Auto-ignition point ……. 225 deg C at 760 mm Hg
Lower explosive limit … 0.6 % (in air)
