Description
Specialized to break emulsion or slop OIL and Water, RXSOL-20-2006-020 has the unique feature that dissociates slop to seperate oil and water. This product is formulated to meet the ever changing regulations for the treatment of tank cleaning waste water after using petroleum based solvents, and Bunker “C” cleaners.
Technical Bulletin
RXSOL-20-2006-020 has the unique feature that dissociates slop to seperate oil and water. This product is formulated to meet the ever changing regulations for the treatment of tank cleaning waste water after using petroleum based solvents, and Bunker “C” cleaners.
Application :::
Ideally suited for slop tanks. Also recommended for local cleaning & degreasing of engine rooms, bilges & tank tops. Low toxicity, non – corrosive. Highly effective, economical solvent cleaner.
DOSE :::
For light contamination dilute with water in the ratio 1:20 . For medium contamination dilute with a petrosolvent. And for heavy contamination concentrated RXSOL-20-2006-025 is suggested.
For Engine Room & Cargo Tank Cleaner
Product Description:- RXSOL-20-2006-025 is an all purpose degreaser emulsifiers, It is an excellent blend of powerful solvent base and emulsifying inorganic products .Specially designed for engine room and cargo tank cleaning .Main feature of RXSOL-20-2006-025 is, it finally dissociate slop emulsion to separate oil and water .This provide us with ability to dispose of waste solution as per MARPOL & IMO rules and regulation .
Dosage:- Dose rate and results will vary depending on amount of contamination . For light contamination dilution with water up to 1:20 is recommended where as medium contamination dilution with Petro solvent , And for heavy contamination neat RXSOL CB 2006 is suggested to use.
Procedure of use :- RXSOL-20-2006-025 is recommended for local cleaning & degreasing of engine rooms, bilges & tank tops. It may be applied by brush, spray, immersion, soaking, or any other conventional means.RXSOL-20-2006-025 is used neat. Allow a residence time of at least 20- 45 minutes where possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed to separate in a holding tank for atleast 3-5 hours before passing through an oily water separator.
Tank Cleaning after Mineral Oils/ Lube Oils / Slope-Black Oil
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a temperature between 65°C & 80°C then stripped constantly and transferred to a holding tank for separation.The time for this will vary depending on amount of RXSOL-20-2006-025 used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly RXSOL-20-2006-025 on tank surfaces to be cleaned, left for at least 30 minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.
Label
RXSOL-20-2006-025 has the unique feature that dissociates slop to seperate oil and water. This product is formulated to meet the ever changing regulations for the treatment of tank cleaning waste water after using petroleum based solvents, and Bunker “C” cleaners.
LABEL PROPERTY
Odour …………………….. Smells of hydrocarbon
Appearance ……………. Liquid, brown,
pH ………………………….. not applicable
Boiling point ……………. 195 °C at 760 mm /Hg
Vapour pressure ……… 1 mbar
Vapour density ………… (air = 1) >1
Melting point ……………. not known
Insoluble in water …….. Specific gravity /(water=1) 0.79
Flash point ……………. 66 deg C (CC)
Auto-ignition point ……. 225 deg C at 760 mm Hg
Lower explosive limit … 0.6 % (in air)
