Description
A powerful penetrating mixed chemical products to remove heavy coal deposits. Additionally, it may also be used to remove mineral deposits and eliminate bad odors in tanks and other closed systems.
It is free from hydrocarbon solvents, non flammable and biodegradable.
Biodegradable / Non-Toxic / Non-Pollutant.
VERY Cost effective.
Recommended to use spray equipment.
The use of hot water will greatly enhance the effectiveness of the cleaning and should be utilized whenever possible.
Technical Bulletin
Coal Remover-Rx (RXSOL-22-2201)
Heavy Duty ( concentrate )
Product Description:-
A powerful penetrating mixed chemical products to remove heavy coal deposits. Additionally, it may also be used to remove mineral deposits and eliminate bad odors in tanks and other closed systems.
It is free from hydrocarbon solvents, non flammable and biodegradable.
Biodegradable / Non-Toxic / Non-Pollutant.
VERY Cost effective.
Recommended to use spray equipment.
The use of hot water will greatly enhance the effectiveness of the cleaning and should be utilized whenever possible.
Directions for Use and Dose Rates
Soak Method:-
It may be used concentrated or diluted with water, depending on the degree of contamination, the surface area to be treated, the desired degree of cleaning and the available downtime.Actually, the user is the best one capable to regulate the quantity and concentration to be used for the situation at hand.In any case, when the accumulation is not heavy, a 50% solution with water must be used. Otherwise,RXSOL-22-2201. can be used undiluted especially when deposition is heavy and hard spots persist.
Cleaning Procedure
Conventional cleaning methods such as a brush,hard sponge, thick and hard broom and /or a mop can be used on heavy duty and hard stain deposits.Note that for heavy accumulations the cleaning procedure might be necessary to be repeated until the results are satisfactory. Furthermore, is important to keep in mind that 1 litre of RXSOL-22-2201 is sufficient to cover a surface area of 8–10 square meters.
NOTE ::: — Let this product soak into the surface for 30-45 minutes. Then using a high-powered spray washer blast the surfaces until the stains and discoloration is gone.
Note:-
• Cleaning time will vary depending on the extract nature and thickness of deposit to be removal.
• Stubborn deposits should be scrubbed to assist the cleaning operation.
Your local Rx CLEANSERS representative will work with you to design the optimum concentration & procedure for your system.
RXSOL-22-2201 should be mixed with fresh water to form a solution of 10-30%, depending on the extent of scaling. After using RXSOL-22-2201 it is essential to thoroughly rinse all metal surfaces at least once with a 0.5% solution of Alkalinity Control in fresh water. This solution should be circulated for 2-4 hours or until an acceptable pH value is obtained. This will neutralize any remaining acidity & passivate steel surfaces.
Product Properties:-
|
Appearance |
Clear (Raw material depended Colour changed of the effectively will , however not be impaired .) |
|
Density |
In g/cm3 at 15°C: 1.03 |
|
Flash Point |
(PMCC)°C: Above 70 |
|
pH |
11 |
|
Compatibility |
|
|
Metal |
No known effect |
|
Rubber |
Avoid natural & synthetic rubber |
|
Packaging |
Order No .:RXSOL-22-2201 |
|
|
Size in liters 25/50/210 |
Safety And Handling :-
“RXSOL-22-2201” is completely safe to handle, being non-toxic & non corrosive.As with all chemicals general safety and handling procedures apply. Avoid contact with eyes as irritation may occur. Do not take internally. In case of contact with eyes, flush eyes immediately and cupiously with clean running water for 15- minutes and seek medical attention.
Characteristics:-
• Use cold – no heating required.
• Easily loosen deposits containing coal carbon .
• Economical to use.
• Scraping not required.
• Non- flammable.
• Helpful for burner tips, fuel injectors and all components fouled by carbon, resin or varnishes.
**Read the Material Safety Data Sheet before using this product.**
Label
High quality product classified as a general cleaner/ remover of coal residues from cargo. COAL REMOVER helps to loosen coal deposit. Also help to remove stains and discolouring after discharge of coal cargoes.
Cost effective SOLUTION for cleaning aſter coal residues, specific ore residues.
Recommended to use spray equipment also can be apply by hand spray method.
The use of HOT WATER will enhance the cleaning effectiveness of COAL REMOVER.
LABEL PROPERTY
Blend mixture of Diluted COAL REMOVER and Diluted Alkaline high foam ship hold cleaning detergent Ship Hold Cleaner / Holdbrite XF, to enhance detergency and cleaning effect.
One part ( A ) of Mixture can be made 1 Ltr Coal Remover with 5 Ltr water, while Other part ( B ) of mixture can be made 1 ltr alkaline detergent like Alkaline high foam ship hold cleaning detergent/holdbrite with 5 ltr water. Then Mix (A) and (B) to spray on coal deposited and stain area.
Other valuable product –
For RUST REMOVING use RXSOL-16-1088-025 And for Cleaning of Lime use RXSOL-67-2213-060, And Cement remover RXSOL-22-2202-025
Precaution : Hand Gloves, Google, Chemical protective Suit.
STOCK POINT – MUMBAI, KANDLA, MUNDRA, KOLKATA, HALDIA, VIZAG, GANGAVARAM, CHENNAI, ENNORE, FUJAIRAH
