Description
Multiclean supplier and Exporter. Multi clean is a specified tank cleaner which has mild alkaline emulsifier cleaning property.
Technical Bulletin
Description :::
This product provides single product simplicity with multi cleaning application flexibility. This formulation provides this unique combination of deep cleaning and odour control features. which can be used to soften up / remove baked-on drying oils and used after the animal and vegitable oils, fish oils, tall oils, tug oils etc. It is free from hydrocarbon solvents, Biodegradable minimizes the extreme hazards to personnel in handling materials.
Provides superior,long-lasting cleaning,stain removal & odor control.
Degrades residual organics (e.g.grease,food spills,urine,etc.) to provide continual deep-cleaning action.
Prevents the growth of undesirable disease-causing organisms.
Keeps drain lines, sumps & septic tanks unclogged and free of odour.
Application Method :::
Use at a concentration of 2% to 5%. Add 20 ml. RXSOL-16-1502-210 to 1 litre of hand-hot water. for SPOT CLEANING purpose.
Use 1.5% solution of RXSOL-16-1502-210 in a bucket of water. for general cleaning. No rinsing needed.
Use a1% solution of RXSOL-16-1502-210 for SPRAY CLEANING
Use 0.2% solution of RXSOL-16-1502-210 For general cleaning where HOT cleaning required
DOSE :::
Using-Procedure:-
First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method is by direct injection followed by recirculation washing, using tank cleaning machines.
Spraying Method:- Spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then Butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages. Inspects tanks(s) and if the desired result has been achieved fresh water rinse and dry.
**Make sure to take all safety precautions are followed when handling/spraying as other GENERAL TANK CLEANER **
Injection Method:- Not applicable.
Re-Circulation Method:- Fill the tank with fresh water and heat up to warm 50 degree C . IF a drop line is available on the tank line system, then start to circulate the water and add the required amount of Caustic flakes and MULT CLEAN to make a 2.5% solution. A stronger solution can be made, but be advised that too much Caustic and too high temperature will result in white powder all over the tank. Under normal circumstances, between 2.5% and 4.5% will be sufficient strength. If there is no drop line, then lower Butterworth hoses into the tank from the pump stack header without machines attached and circulate through these hoses while you fill the solution material.
Use a strainer at the pump stack when circulating any solution. Tank Lining– Stainless / Epoxy / Phenolic.
Technical Specification :::
PHASE : liquid
Specific Gravity @ 250C : 1.1
pH ( 1% solution) : 9.5
pH range : Alkaline
Flash point : Non-flammable
Shelf Life & Storage : 2 years at 20 C to 350 C. Store in cool, dry place.
While this product in non-toxic, non-corrosive and non-poisonous, it is nevertheless wise to keep it out of reach of children and to follow basic precautions of use. Wash hands with warm, soapy water after use. Avoid contact with eyes, open cuts or sores. In case of eye contact, flush with water for 15 minutes. Call a physician. Do not use this container for storing beverages or other liquids. Contains BioActive formulation contains no phosphorus.
Label
Not classified as dangerous for users
S2: Keep out of reach of children
PROPER SHIPPING NAME: Not Regulated
UN Number : —- Class : – Packing Group :—
EmS:- Marine pollutant: No
LABEL PROPERTY
Product Properties
Odour ……………………Odourless
Appearance …………..Liquid, pale yellow, soluble in water
pH …………………………8.5 – 9 at 100 % concentration
Boiling point > ………100 °C at 760 mm /Hg
Vapour pressure……..not known
Freezing point………….< 0 °C at 760 mm/Hg
Completely soluble in water
Specific gravity (water=1).......1.03
Non combustible
