Description
Especially formulated for tank cleaning where Hydro Carbon Free techniques and more concentrated product with less foam is required to soften up / remove baked on drying oils and also used after animal and vegetable oils, fish oils, tall oils,tug oil etc. It is low toxic product with an exceptional solvency power on soil & oily matter .It is free from hydrocarbon solvents and minimizes the extreme hazards to personnel in handling materials.
Powerful solvency
Moderate evaporation rate
Low viscosity
High dilution ratio
Low surface tension
Coupling ability
Wide range of applications
Technical Bulletin
HCF Remover HD
RXSOL-20-2013-025
Description:–
A very strong low foaming cleaner, Especially formulated to soften up / remove baked on drying oils and also used after animal and vegetable oils, fish oils, tall oils, tung oil etc. It is low toxic product with an exceptional solvency power on soil & oily matter . It is free from Hydrocarbon solvents and minimizes the extreme hazards to personnel in handling materials.
Using Procedure:-
First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2013-025 is by direct injection followed by recirculation washing, using tank cleaning machines.
Spraying Method:- Using HCF as delivered in drums, spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages. Inspects tanks(s) and if desired result has been achieved fresh water rinse and dry.
**Make sure to take all safety precautions are followed when handling / spraying HCF**
Injection Method– not applicable.
Re-circulation Method– Fill tank with fresh water and heat up to warm 50oC . IF a drop line is available on the tank line system, then start to circulate the water and add the required amount of Caustic flakes and HCF to make a 2.5% solution. A stronger solution can be made, but be advised that too much Caustic and too high temperature will result in white powder all over the tank. Under normal circumstances, between 2.5% and 4.5% will be sufficient strength. If there is no drop line, then lower butterworth hoses into the tank from the pump stack header without machines attached and circulate through these hoses while you fill the solution material.
** Use a strainer at the pump stack when circulating any solution.**
Tank Lining– Stainless / Epoxy / Phenolic / Zinc-silicate.
Characteristics:
- Removes grease, oil, carbon deposits, soil and grime.
- Keeps loosened deposits in suspension preventing re-deposition.
- Low toxic. , Non-flammable.
- Free from hydrocarbon solvents.
- Effective and economical in use , Water-based cleaner.
- RXSOL-20-2013-025 has numerous cleaning applications including removal of greases, waxes, oil, sludge, soot, carbon deposits and general dirt and grime.
- Non-corrosive to ferrous metals. Suitable for all tank-coatings.
- Can be used for gas and hydrocarbon freeing of tanks.
- Can be used for deodorizing
- Contains wetting agents.
Note:- Completely miscible with sea water.
Label
RXSOL-20-2013-025 can be used for similar applications of RXSOL-20-2013-025 , where a more concentrated product is required., Especially formulated for tank cleaning where Hydro Carbon Free techniques are employed to soften up / remove baked on drying oils and also used after animal and vegetable oils, fish oils, tall oils,tug oil etc. It is low toxic product with an exceptional solvency power on soil & oily matter .It is free from hydrocarbon solvents and minimizes the extreme hazards to personnel in handling materials.
PACKAGING : 25 ltrs , 210 ltrs.
COMMON NAME : H C F REMOVER
LABEL PROPERTY
General Information
Form : Fluid
Colour : Yellowise / Clear
Odour : Characteristic
• Change in condition
Melting point/Melting range : Undetermined.
Boiling point/Boiling range : 171°C
• Ignition temperature : 240°C
• Self-igniting : Product is not selfigniting.
• Danger of explosion : Product does not present an explosion hazard.
• Explosion limits :
Lower : 1.1 Vol %
Upper : 10.6 Vol %
• Vapour pressure at 20°C : 23 hPa
• Density at 20°C : 1.01 g/cm³
• Solubility in / Miscibility with
water : Fully miscible.
• pH-value at 20°C : > 7
